bồn Lavabo Rửa Mặt
gạch mosaic
gạch bông
gạch mosaic thẻ que
gạch lát nền
keo silicon axit
gạch bông lát nền
máy khoan bê tông Bosch 
máy cắt sắt bosch
Giỏ hàng
ISONEM MS Polymer High Performance Acrylic Polymer / Waterproof Material for Concrete and Metal Roof and Terrace
(31 Lượt)
Nhà sản xuất, chế tạo • 2 năm •
VN
VN
ISONEM MS Polymer High Performance Acrylic Polymer / Waterproof Material for Concrete and Metal Roof and Terrace
Các đề xuất khác cho doanh nghiệp của bạn
Gợi ý sản phẩm tương tự để bạn so sánh nhanh và gửi yêu
cầu báo giá.
ISONEM Super Elastic Exterior and Interior Home Wall Paint UV Resistant Waterproof Coating Made in Turkey
88,000đ
1 piece (Tối thiểu)
ISONEM Thermal Roof Paint Eco-Friendly Heat Reflective Liquid Insulation Coating Manufacturer From Turkey
90,000đ
1 piece (Tối thiểu)
ISONEM L ONE COMPONENT Economical Water-Based Transparent Waterproofing Material All Surface Ready to Use Solution
118,000đ
1 piece (Tối thiểu)
ISONEM M 36 QUICK SETTING CEMENT BASED WATER PLUG MORTAR INSTANTLY STOPS LEAKING WATER, MANUFACTURER FROM TURKEY
50,000đ
1 piece (Tối thiểu)
Những điểm chính về sản phẩm
Thuộc tính cụ thể của ngành
Các thuộc tính khác
Khu vực
Thương hiệu
Mã sản phẩm
Tên sản phẩm
ISONEM MS Polymer High Performance Acrylic Polymer / Waterproof Material for Concrete and Metal Roof and Terrace
Nhà cung cấp
CÔNG NGHỆ SƠN VÀ CÁCH NHIỆT ISONEM
Thông tin nha cung cấp của bạn
2 yrs
Vị trí tại VN
Mô tả sản phẩm
Products Description
ISONEM MS POLYMER
ISONEM MS POLYMER is a one part, solvent-free, pure acrylic- based special waterproofing polymer produced by the latest
technology. It is ready to use, UV resistant, bright, hard elastic and walkable. It is not affected by pedestrian and vehicle
traffic and chemicals. It is used as an insulation material on terraces, roofs, balconies and wet rooms, industrial floors,
concrete, alum, plaster, wood surfaces, spray polyurethane- applied surfaces, sidings and foundation walls; and also used as a coloured coating on factory, depot, parking lot and walkway, asphalt road. As it dries too fast, it is easy to work and quick. Very economical due to its low consumption. Applicable to any surfaces.
Uses
* Insulations of roof terrace and balconies
* Insulations of wet room and foundation walls
* Floors of factory and depot
* Park and walk ways
* Water lakes, terraces and roofs
* In all kinds of poor subsoils
* In exteriors
* In metal roofs, woods
* On bituminous problematic insulations
* On asphalt and concrete surfaces.
Easily applied as a waterproofing agent for roofs and balconies, canals,chimney surroundings, gutters and strainers in wide area and detailed, flat or inclined roofs.
Characteristics /Advantages
* Ready to use
* Low labour cost
* Remains flexible at low temperatures
* Permits water vapour to the surface
* Can be thinned with water, solvent-free
* Can be painted with acrylic based paints
* Can be coloured with water based pasty pigments
* UV resistant
* Not affected by pedestrian and vehicle traffic
* Does not require protective alum or concrete
* Applied easily on wet and moist surfaces in all weather conditions, summer- winter
* Non- flammable
TECHNICAL PROPERTIES
Form: Appearance / Colour; Liquid / clear, white,or in any colour.
Chemical Base: Acrylic based liquid
Density: 1.06+0.05 kg/dm3, + 20 0C
pH: 6 - 9
Solids Content: % 52+3, 105 0C
Elongation at Break: Min. % 250 (for 1 mm thickness, at +20 0C, after 72 hrs)
Application Temperature: +5 °C - +35 °C
Interval between each application: approx. 4 hours
APPLICATION PROCEDURE
Substrate Quality / Preparation
- Substrate must be clean, uniform, dry, free of dust, oil or grease and loose or weak particles
- Plastered and concrete surfaces should be cleaned with 1:10 ISONEM UNI-CLEAN : water solution. Rinse the surface with clean water afterwards
- Surface defects and voids should be repaired with ISONEM M 03 repair mortar
- Steel surfaces should be painted with suitable anti-corrosion material before application.
ISONEM MS POLYMER, diluted to 200%, should be used as a primer on surfaces like eternit, foamed blocks, brick, tile, masonry, concrete and plaster.
Application Conditions / Limitations
Substrate Temperature min. +5°C, max. +35°C
Ambient Temperature min. +5°C, max. +35°C
Application Instructions
Application Method / Tools
Application can be done by brush, roller, or spray gun. First layer should be applied in one direction only and following layer to be perpendicular to the previous one.
Waiting Time /Overcoating
Waiting time depends on the ambient temperature, substrate temperature, relative humidity and the thickness of coating applied. Before applying the second layer, make sure that the first layer is totally cured and dry. Wait 4 hours (at 23°C and %50 relative humidity).
Notes on Application /Limitations
- This product is not generally suitable on its own for waterproofing against hydrostatic pressure.
- It is recommended to reinforce the vertical and horizontal joints of excessively cracked surfaces by using geotextile protection layer.
- Freshly applied material should be protected from rain and/or frost for 24 hours.
- ISONEM MS POLYMER should not be applied during rain, fog and temperatures below +5°C.
Curing Details
ISONEM MS POLYMER is applied at 23°C:
- Achieves its mechanical strength after three days
- Becomes fully waterproof after almost five days
- Reaches its final strength values after seven days
- At low temperatures, above mentioned durations can be longer
All the afore-mentioned times refer to +23 oC and 50% relative humidity. Higher temperatures and lower humidity rates quicken, whereas lower temperatures and higher humidity rates slow down the drying process.
CONSUMPTION: for transparent applications on ceramic, tile etc surfaces approx. 150 gr/m2, on concrete, alum and plaster surfaces approx. 500 gr/m2
Packaging: 5 kg, 10 kg, 18 kg plastic pails
technology. It is ready to use, UV resistant, bright, hard elastic and walkable. It is not affected by pedestrian and vehicle
traffic and chemicals. It is used as an insulation material on terraces, roofs, balconies and wet rooms, industrial floors,
concrete, alum, plaster, wood surfaces, spray polyurethane- applied surfaces, sidings and foundation walls; and also used as a coloured coating on factory, depot, parking lot and walkway, asphalt road. As it dries too fast, it is easy to work and quick. Very economical due to its low consumption. Applicable to any surfaces.
Uses
* Insulations of roof terrace and balconies
* Insulations of wet room and foundation walls
* Floors of factory and depot
* Park and walk ways
* Water lakes, terraces and roofs
* In all kinds of poor subsoils
* In exteriors
* In metal roofs, woods
* On bituminous problematic insulations
* On asphalt and concrete surfaces.
Easily applied as a waterproofing agent for roofs and balconies, canals,chimney surroundings, gutters and strainers in wide area and detailed, flat or inclined roofs.
Characteristics /Advantages
* Ready to use
* Low labour cost
* Remains flexible at low temperatures
* Permits water vapour to the surface
* Can be thinned with water, solvent-free
* Can be painted with acrylic based paints
* Can be coloured with water based pasty pigments
* UV resistant
* Not affected by pedestrian and vehicle traffic
* Does not require protective alum or concrete
* Applied easily on wet and moist surfaces in all weather conditions, summer- winter
* Non- flammable
TECHNICAL PROPERTIES
Form: Appearance / Colour; Liquid / clear, white,or in any colour.
Chemical Base: Acrylic based liquid
Density: 1.06+0.05 kg/dm3, + 20 0C
pH: 6 - 9
Solids Content: % 52+3, 105 0C
Elongation at Break: Min. % 250 (for 1 mm thickness, at +20 0C, after 72 hrs)
Application Temperature: +5 °C - +35 °C
Interval between each application: approx. 4 hours
APPLICATION PROCEDURE
Substrate Quality / Preparation
- Substrate must be clean, uniform, dry, free of dust, oil or grease and loose or weak particles
- Plastered and concrete surfaces should be cleaned with 1:10 ISONEM UNI-CLEAN : water solution. Rinse the surface with clean water afterwards
- Surface defects and voids should be repaired with ISONEM M 03 repair mortar
- Steel surfaces should be painted with suitable anti-corrosion material before application.
ISONEM MS POLYMER, diluted to 200%, should be used as a primer on surfaces like eternit, foamed blocks, brick, tile, masonry, concrete and plaster.
Application Conditions / Limitations
Substrate Temperature min. +5°C, max. +35°C
Ambient Temperature min. +5°C, max. +35°C
Application Instructions
Application Method / Tools
Application can be done by brush, roller, or spray gun. First layer should be applied in one direction only and following layer to be perpendicular to the previous one.
Waiting Time /Overcoating
Waiting time depends on the ambient temperature, substrate temperature, relative humidity and the thickness of coating applied. Before applying the second layer, make sure that the first layer is totally cured and dry. Wait 4 hours (at 23°C and %50 relative humidity).
Notes on Application /Limitations
- This product is not generally suitable on its own for waterproofing against hydrostatic pressure.
- It is recommended to reinforce the vertical and horizontal joints of excessively cracked surfaces by using geotextile protection layer.
- Freshly applied material should be protected from rain and/or frost for 24 hours.
- ISONEM MS POLYMER should not be applied during rain, fog and temperatures below +5°C.
Curing Details
ISONEM MS POLYMER is applied at 23°C:
- Achieves its mechanical strength after three days
- Becomes fully waterproof after almost five days
- Reaches its final strength values after seven days
- At low temperatures, above mentioned durations can be longer
All the afore-mentioned times refer to +23 oC and 50% relative humidity. Higher temperatures and lower humidity rates quicken, whereas lower temperatures and higher humidity rates slow down the drying process.
CONSUMPTION: for transparent applications on ceramic, tile etc surfaces approx. 150 gr/m2, on concrete, alum and plaster surfaces approx. 500 gr/m2
Packaging: 5 kg, 10 kg, 18 kg plastic pails
Product Name: | ISONEM MS Polymer High Performance Acrylic Polymer / Waterproof Material For Roof and Terrace |
Type: | Other Waterproofing Materials |
State: | Liquid Coating |
Main Raw Material: | Acrylic |
Usage: | Building Coating, Waterproofing Material |
Application Method: | Spray, Brush, Roller |
Color: | Clear and all colors available |
Certificates: | ISO9001-2015 |
Related Products
Company Profile
5 CONTINENTS, IN NEARLY 100 COUNTRIES,
ISONEM PAINTS AND INSULATION TECHNOLOGIES INC. was established in Izmir in 2004.It has assumed the leading role with the innovations it has brought up to the sector with its research and development (R & D) team, each of which is specialized in his/her branch at a 7500 m2 closed modern production site landed on an area of 10000 m2 within ITOB Organized Industrial Zone. We have presented the innovative products for defence, energy, agriculture and industrial field and the thermal, sound, fire, water insulation and special chemical products that we have developed to the usage of the mankind and the whole world.
We have managed to have our name echoed via both domestic and foreign successes that we have achieved by adopting sustainable quality as a principle within every stage by using high technology since the beginnings of our organization.
We have achieved to be a Turkish Company and Trade Mark through our activities in Europe, Africa and Far East which is known well by the whole world in its field by executing exports to approximately 100 countries, basically China, Korea and USA.
Besides our commercial and sectorial success, we have been aware of the fact that today’s world is entrusted to us for the mankind of tomorrows, since we have never used biocidal raw materials within our products as an outcome of our awareness for the environment.
As Isonem, our mission is protecting the nature via electricity generating external housepaints, paints which convert CO2 into Oxygen and many innovative products; and to present a better world worth living.
ISONEM PAINTS AND INSULATION TECHNOLOGIES INC. was established in Izmir in 2004.It has assumed the leading role with the innovations it has brought up to the sector with its research and development (R & D) team, each of which is specialized in his/her branch at a 7500 m2 closed modern production site landed on an area of 10000 m2 within ITOB Organized Industrial Zone. We have presented the innovative products for defence, energy, agriculture and industrial field and the thermal, sound, fire, water insulation and special chemical products that we have developed to the usage of the mankind and the whole world.
We have managed to have our name echoed via both domestic and foreign successes that we have achieved by adopting sustainable quality as a principle within every stage by using high technology since the beginnings of our organization.
We have achieved to be a Turkish Company and Trade Mark through our activities in Europe, Africa and Far East which is known well by the whole world in its field by executing exports to approximately 100 countries, basically China, Korea and USA.
Besides our commercial and sectorial success, we have been aware of the fact that today’s world is entrusted to us for the mankind of tomorrows, since we have never used biocidal raw materials within our products as an outcome of our awareness for the environment.
As Isonem, our mission is protecting the nature via electricity generating external housepaints, paints which convert CO2 into Oxygen and many innovative products; and to present a better world worth living.
Certifications
Product packaging
Packaging And Shipping: | 18 kg pail, 27 pails/pallet | |
MOQ: | 486 kg | |
Delivery Time: | 3-5 days after transferring of the payment | |
As Per International Standards | ||
Contact Us
Factory (Head Office): | ITOB OSB 10001 Street No: 20 Tekeli Menderes / IZMIR - TURKEY |
Phone: | +90 (533) 581 05 54 |
Fax: | +90 (232) 437 01 33 |
Website: | www.isonem.com |
Giá
125,000 đ
Shipping/Vận chuyển
Dịch vụ chuyển phát nhanh toàn quốc (Tiêu
chuẩn)
Thời gian giao hàng: Liên hệ
Bảo vệ cho sản phẩm này
Giao hàng
qua Daisan Logistics
Dự kiến đơn hàng của bạn sẽ được giao trước ngày dự kiến hoặc nhận
khoản bồi thường chậm trễ 10%
Thanh toán an toàn
Mọi khoản thanh toán bạn thực hiện trên Daisan.vn đều được ...
Chính
sách hoàn tiền
Yêu cầu hoàn lại tiền nếu đơn đặt hàng của bạn không được vận chuyển,
bị thiếu hoặc giao đến có vấn đề về sản phẩm
Sản phẩm khác cùng danh mục
Những lựa chọn tương tự để bạn tham khảo thêm.
ISONEM Super Elastic Exterior and Interior Home Wall Paint UV Resistant Waterproof Coating Made in Turkey
88,000đ
1 piece (Tối thiểu)
ISONEM Thermal Roof Paint Eco-Friendly Heat Reflective Liquid Insulation Coating Manufacturer From Turkey
90,000đ
1 piece (Tối thiểu)
ISONEM L ONE COMPONENT Economical Water-Based Transparent Waterproofing Material All Surface Ready to Use Solution
118,000đ
1 piece (Tối thiểu)
ISONEM M 36 QUICK SETTING CEMENT BASED WATER PLUG MORTAR INSTANTLY STOPS LEAKING WATER, MANUFACTURER FROM TURKEY
50,000đ
1 piece (Tối thiểu)
Sản phẩm có thể bạn quan tâm
Những lựa chọn bạn có thể quan tâm để tham khảo thêm.
Classical Design Electric Motorcycle 1200W Moto Electric Motorcycle Scooter High Speed Adult
4,975,000đ
1 piece (Tối thiểu)
Cheap Prices Epa Dot Certified 2000w Motor High Speed for Racing Electric Scooter Motorcycle With Coc
9,975,000đ
1 piece (Tối thiểu)
Oversea Warehouse High Speed Electric Touring MotorBike 500W 48V 12Ah Hub Motor Electric Moped Scooter
3,475,000đ
1 piece (Tối thiểu)
Waterproof High Mildew Proof Weather Resistance Ms for Rv Wood Floor Metal Steel Weatherproof Silicone Sealant
Liên hệ
1 piece (Tối thiểu)
Sản phẩm phổ biến của nhà cung cấp
ISONEM Self-Leveling 3K Food Grade Floor Coating Modern Design Chemical Resistant Epoxy Resin Based
208,000đ
1 piece (Tối thiểu)
ISONEM THERMAL PAINT (Thermal Insulation, Heat Insulation Paint for Exterior and Interior Wall) - 10 LITERS SIZE
90,000đ
1 piece (Tối thiểu)
ISONEM SS SOIL HARDENER STABILIZER DUST CONTROL AGENT ECO FRIENDLY WATER BASED SAFE MATERIAL MADE in TURKEY
110,000đ
1 piece (Tối thiểu)
Tìm sản phẩm bằng hình ảnh
Dán ảnh bằng Ctrl + V hoặc kéo thả ảnh vào đây
hoặc tải ảnh từ máy tính